Modules and Kits from Synovatron

Updated 31st January 2021: Synovatron will cease to trade from 1st February 2021 onwards. The following products will no longer be available from Synovatron Limited. Some items will be available from retailers and I will post the status of those when I know the final state:

CVGT1 - 8HP Euro to Buchla CV-gate-trigger-pulse translator
No longer available directly - please check out Noisebug or SchneidersLaden who have may stock of modules.

VXP1 - 14HP Voyager Output Expander
No longer available

VXP1-OS - 14HP Old School Voyager Output Expander
No longer available

Jacks - 4HP 3.5mm minijack to 1/4" jack format jumber
No longer available directly - this may become available for sale by another company - watch this space, I will update when I know

Euro Bananas - 6HP 3.5mm minijack to 4mm banana socket format jumbler
No longer available directly - this may become available for sale by another company - watch this space, I will update when I know

Trunks & Mults - 6HP 8-channel trunk lines and two 4-way multiples
No longer available directly - this may become available for sale by another company - watch this space, I will update when I know

More info on Jacks, Euro Bananas and Trunks & Mults modules and kits on this page.  

Euro Bananas, a pair of Trunks & Mults, Jacks, CVGT1 and VXP1

Limited edition Black Gold CVGT1 (SOLD)

Modular in a tool case

I had a day free on Saturday and set about putting a modular in a tool case. To be exact it is a Doepfer A-100 DIY kit #1 fitted to a Halfords engineers tool case. The point of this was to have an easily transportable demo system so I can take to shows, meets etc in order to show how lovely my CV Tools module is and to let people have a play.

In a follow-on to my cheap DIY store front panels post a few weeks back I used anodised aluminium angle strips in the construction from Homebase - the case is bigger than the 6U 84HP of the rack kit.
(Note to non-UK readers Halfords is a motor accessories store and Homebase is a DIY store)

Here's the case

Prep the case - remove separators, tool panel and unecessary fixings.

All done, ready to start serious modding

This will be powered by a 15VAC supply so a nice big hole for an XLR connector

XLR in place (EDIT: this is eventually replaced by a plug version as a power lead with exposed pins is bad karma)

A bit of judiscious foam cutting to neaten it up

Markout and drill the regulator boards fixing points - 4 x M3

Regulator screwed in place

I used M3 washers to spread the load - the case is just hardboard with a thin aluminium veneer

Position the bus boards and drill mounting holes - long M3 screws with tapped spacers fitted

All electrics now in place. Note this is temporary - there will be wiring to a front panel power switch on the next installment!

Next make the rack end pieces out of 10mm x 20mm anodised aluminium angle strip. These make the rack the perfect width to fit the case.

Similar to above I made top and bottom strips to fill the gap - I used 25mm x 25mm anodised angle, again an almost exact height fit - starting to look good.

Here's a view showing the fixings (ok I drilled a hole in the wrong place. Motto: measure twice, cut once!!!).

As I said a near perfect fit in the case. At this point just resting on the foam and not screwed in. That's in the next installment.

Loaded with modules and powered up. Take no notice of the modules selection, I've since changed it to a more coherent set.

Even a nifty scope showing VCOs, Synovatron DioDe and CV Tools in operation - now that's a waveform!

 Next installment will add a power switch and fixings to anchor the rack to the case. It will also make use of all that front panel space top and bottom for passive and buffered mults, bus access, simple LFOs, gate logic, 3.5mm to 6.25mm/RCA adaptors, etc etc (the thought of the lovely goodies that will get built in is going to keep me awake a night - so sad!!)

Here's a short clip of it working:-

New generic front panels for DIY kits

I now have stock of a range of 4HP and 8HP front panels to suit the Synovatron DIY Prototyping Kits. These can be purchased with the kits as an option or separately. 

The 8HP panel suits DIY Kit 1 and has two variants, one to suit a column of jacks (8.2mm holes) and a column of pots (7.5mm holes). The other variant has 3mm pilot holes to give you the flexibility to mix and match front panel components by drilling out to suit jacks, pots or switches, or left as is for 3mm LEDs.

The 4HP panel suits DIY Kit 3 and also has two variants, one to suit jack sockets (8.2mm holes) and the other with just 3mm pilot holes so they can easily be modified to larger diameters for jacks or switches or left as is for LEDs.

The panels are made from 2mm aluminium and have a brushed, clear anodised finish.  The mounting holes (slots) are suitable for both Doepfer and Analogue Systems hole pitches.

These panels make the kits more complete and I will also offer a set of knobs in DIY Kit 1 to finish it off.

Kit 1 options: The soft-touch knobs can be ordered in white, grey, red, orange, yellow, green or blue.

Prices range from £5.99 to £8.99 if ordered separately, a bit cheaper if ordered with a kit. The knobs are £1.25 for 5 if ordered with a kit.

The panels will also include a set of M3x6 screws and plain washers.

Update:

Here's a 8HP pilot hole panel that I drilled out for a customer so he could mount a mult on the left and an OSC303 on the right (Note: he bought the OSC303 as a kit without front panel and jacks. There's no point in trying to do this if you have one DinSyncs's excellent clear blue panels). The jacks were drilled out to 8mm, the pot to 7.5mm and the switch to 6mm. Looks pretty sexy!

Tone's top tips:  

(1) Cover the panel in masking tape so the swarf doesn't scratch the front finish. 

(2) start with smaller drill sizes and work up to the final size else you may end up with odd shaped holes.

(3) Deburr holes on both sides with a countersink bit.