Another custom built Euro to Buchla Translator module

I was recently commissioned by a client to build a custom Euro Buchla interface module, similar to the two I previously built, but with offset switching. The previous two designs both had fixed offset and gain and were intended for use with envelopes, LFOs etc. In other words there was no 1V/octave to 1.2V/octave scaling required just offsetting to ensure the Euro signals stayed in the 0-10V range of the Buchla (you can refer back to my earlier post here).

This module is intended to be used alongside my client's CVGT1 module (which provides the ground reference connection) and adds more CV channels. My client uses Expert Sleepers' SilentWay software for pitch sensitive CV and was not interested in scale conversion as the software does the necessary recalibration however he also wanted the flexibility to be able to interface envelopes, transients and LFOs and so wanted to be able to DC shift signals when he needed to.

The spec was 4 channels of Euro to Buchla (scale of 1, 0V or +5V offset) and 1 channel of Buchla to Euro (scale of 1, 0V or -5V offset); so 10 connectors a 5 switches in 8HP.  

My 8HP prototyping panels proved to be difficult as the existing hole positions meant that the connectors and switches would have been too close to each other plus I only had a few left and found they were scratched; they got binned. I used Schaeffer for a quick-turnaround panel; not cheap but very well made. In a moment of madness I got 5 panels made, including engraving (which the original 2 modules didn't have).

Some Preliminary Work on a ModuleModule Design

ModuleModule CV and gate/trigger translator

This is just a quick post to show what I have been doing with regard to the ModuleModule design I mentioned in my last blog post. More info will unfold over the next weeks but this is just to let several Muffwigglers know that I am progressing their ideas (albeit a bit slowly). These are just a first draft and the design will change. The idea is that there will be a common design that supports either Buchla/Euro or Buchla/Serge; the only difference being the connectors used. It's difficult fitting all I want in the smaller ModuleModule format - perhaps the trim pots will come out and I'll add scale switches as per the CVGT1 - your feedback would be valuable!

CV2 - a sister module for the CVGT1

This is another idea I've been mulling over which will complement the CVGT1 and is intended for non-pitch critical CVs and for audio level translation. Again it's just a preliminary idea and feedback is welcomed.

Wishing you all a happy 2013

2012 for various reasons has been for me a real struggle and so am hoping 2013 will turn out to be a better year. My wish on this first day of 2013 is that it will be a very happy and healthy year for you and your loved ones.

2012 saw just a few successes:-

The first was the power system and trunk-line modules I designed and built for Gregg Wilson's wonderful wall sized monster synth.

The second was the development, prototyping (including two custom built modules) and preproduction run of the CVGT1 Euro Buchla translator module which are now delivered to the pre-order list customers who are putting them to good use.

Related to the CVGT1 was my first foray into surface-mount boards - the preproduction run of 30 CVGT1 modules used through-hole components which meant that I could, and did, hand build those modules. However they were so time consuming to build that I got quotes for getting them made but the cost was was prohibitive; I was advised that surface mount assembly would be much cheaper and so I set about relaying the boards for surface mounted components.  This worked well and they worked first time albeit for the most significant financial commitment I have made in Synovatron to date. 

CV Tools may get the same reworking but will keep the through-hole version in existance for you DIY enthusiasts; the CV Tools DIY Kit has continued to be a succesful product with more plaudits about the kit presentation, clear instructions and ease of build.

The downside for 2012:-

  
Following a personal loss in July I took some time out and then I pushed very hard in the last 2-3 months to produce a large batch of CV Tools and CVGT1 modules for the end of 2012 but due to supplier quality issues it now looks like those modules will not ship to distributors until late January to early February. 

I had to reject two thirds of CVGT1 front panels due to scratches and had to reject a batch of 1000 jack sockets due to varying quality from stiff to non-functional (i.e. can't insert a patch lead); unfortunately many were assembled on boards before I discovered this. So all in all a huge amount of effort and frustration with no output but I have learned lessons from this. 3.5mm connector quality is certainly the hardest component problem that Eurorack manufacturers seem to face followed closely by front panel quality issues.

Another problem encountered but Eurorack users is the ease of misconnecting the power cable. 

This was brought sharply into focus by a client who reverse connected his RS-35 using one of my ASM2DB Adaptors and blew up the tantalum capacitors and a CA3046 IC on the RS-35; notably all the TL072 ICs survived as did the F-V converter chip. 

The connection instructions are clear but we are human and our capacity to f**k up goes with the territory (hence the disclaimer in the instructions); I still do it even though I know to be careful. I have fixed his module for free as a goodwill gesture but it does worry me - my plea to all designers of new modules is use protection diodes.

Euro and Buchla working together

Here's a short video by Eldancer showing the buchla and Euro systems workng together. Both the CVGT1 and a custom euro Buchla interface module I made a while back are in use here (top right hand corner). They don't get the limelight, they just allow the conversation to occur, working quitely in the background :)



mutipatch 1 from Eldancer on Vimeo.

A quick update on CVGT1 Modules

About half of my pre-order list for CVGT1 modules have been delivered and the rest will go out within the next month. Within a couple of months they will appear with distributers but I am having to look at relaying the boards for surface mount to keep assembly costs down - I don't want the price to go up and I cannot keep building them myself - after building 60 CV Tools and 20 CVGT1 modules (220 circuit boards in all) I am all soldered out. CV Tools will also get relaid for surface mount but I will still keep a through hole stock (currently sold out) for DIY kits.  Watch out for my next update in a month.

Announcing Synovatron's second module CVGT1

Sneak preview

The new module is a Eurorack format Eurorack/Buchla translator called CVGT1. It allows Eurorack and Buchla synths to interact with each other, as the name suggest it provides a CV and a Gate/Trigger interface. Not only does it provide the correct format connectors (and adheres to the Buchla color code) but it also deals with the CV scaling and offsetting and the gate/trigger and timing pulse conversion required to allow control in both directions.

The module is in final stages of build and will need to undergo design proving tests before I release it into the world. So far the front panels are complete and all the components are in stock except for the slightly important PCBs which are due in tomorrow (18th July 2012). The intended launch date is Saturday 21st July at the Brighton Modular Meet at the University of Sussex just outside Brighton UK. 

Here are some quick photos of the panels and partial assembly.  I will follow up in a few days with better photos of the fully assembled module, further details and User Manual download link.

1200HP Monster Synth

I met with Gregg Wilson at the last Brighton Modular Meet. We had talked about the possibilities of this project prior to the meet as he had bought a CV Tools from me. Anyway I ended up building the power supply and Trunk-line modules for his brainchild 1200HP wall mounted synth over the ensuing months so thanks Gregg for placing your trust in me. It is not only amazing as an instrument but also also as a visual feast - a fine piece of active wall art - well conceived and nicely built. The surrounding backlighting sets it off a treat.

The fantastic Wenge wood case was made and installed by Ross Lamond of Lamond Design; This guy rocks!.

Here are a couple of videos of what any synth does best - being used! Enjoy.



Modular Synth Live Performance 1 from Gregg Wilson on Vimeo.

Modular Synth Live Performance 2 from Gregg Wilson on Vimeo.

I Dream of Wires 2: A documentary

A very inspirational video; certainly from my perspective as a small manufacturer of synth modules. Modcan's Bruce Duncan and Intellijel's Danjel Van Tijn give the low-down on their synth building ethos. I have huge respect for these guys for their achievements, products and thinking. Check this out.